November 16, 2026
How to Properly Size a Diesel Generator for Critical Equipment
By @industrialworkbench
Choosing the right diesel generator for essential equipment is not a matter of picking the biggest model you can afford. Oversizing wastes fuel and money. Undersizing risks damage to your equipment or a blackout when you need power most. The process comes down to matching the generator's output to the real electrical demands of the equipment it will support. This article walks through the steps and the key decisions at each point.
Step 1: List Every Piece of Equipment and Its Power Rating
Start with a complete inventory of every device that must run on the generator. Include lighting, pumps, computers, motors, compressors, and any other load. For each item, find the nameplate rating. This is usually printed on a sticker near the power cord or on the back of the unit. The rating is given in watts (W) or amps (A) at a specific voltage.
If the rating is in amps, convert to watts using the formula: watts = volts x amps. For single-phase equipment in North America, use 120 V or 240 V. For three-phase equipment, multiply the result by the square root of three (about 1.73). Write down the running watts for each item.
What to watch: Some equipment lists a running current and a separate starting current. Refrigerators, air conditioners, pumps, and motors draw several times more current for a second or two when they start. That starting current can be two to seven times the running current. A generator must handle the highest starting surge of any single device, plus the running load of everything else that is already on.
Step 2: Calculate the Total Running Load
Add the running watts of all the equipment you listed. This gives you the base load. For example, a small workshop might have lights (400 W), a computer (200 W), a pump (800 W), and a fan motor (500 W). The total running load is 1900 W.
But a generator should not run at 100% of its rating for long periods. A healthy operating range is 60-80% of the generator's rated output. This keeps the engine from being overloaded on a hot day and leaves headroom for future additions. So divide your total running load by 0.75 (a typical target load factor) to find the minimum generator size. In the example, 1900 W / 0.75 = roughly 2533 W. That means a generator rated at 2500 to 3000 W would be appropriate for the running load alone.

What to watch: Do not forget loads that run intermittently. A battery charger may draw a high current for a short time and then drop to a trickle. A welder may have a duty cycle. Account for the peak draw, not the average.
Step 3: Account for Starting Surge
Starting surge is the biggest trap in generator sizing. A motor can draw several times its running current for a fraction of a second. A generator's alternator must supply that surge without the voltage dipping so low that the motor stalls or the generator trips offline.
Check the nameplate for the locked-rotor amps (LRA) or starting amps. If that number is not given, assume the starting surge is three times the running current for most motors. For a pump that draws 800 W running (about 6.7 A at 120 V), the starting surge could be 2400 W (20 A). If that pump is the single largest motor in your load, you need a generator that can deliver at least 2400 W momentarily.
Most generator manufacturers publish a surge rating, often called "starting power" or "peak watts." The surge rating is usually 1.2 to 1.5 times the rated output. A 3000 W generator might have a surge rating of 3600 W. That may handle the pump's 2400 W surge, but if you have a large motor, check the numbers carefully.
What to watch: Multiple motors starting at the same time compound the surge. Stagger the startup of large loads. A generator with a good voltage regulator and a robust alternator handles surge better than a cheap one with the same rating.
Step 4: Consider Fuel Consumption and Runtime
Diesel generators are known for efficiency and long life, but fuel consumption varies with load. A generator running at 25% load uses more fuel per kilowatt-hour than one running at 75% load. That is because the engine still has to overcome its own friction and cooling losses.
If you plan to run the generator for many hours at a stretch, choose a size that keeps the load in the sweet spot. A generator that is too large for the load will run lightly loaded, waste fuel, and may suffer from wet stacking - a condition where unburned fuel accumulates in the exhaust system and damages the engine over time.
What to watch: Check the manufacturer's fuel consumption curves if available. A load bank test during commissioning can verify actual fuel burn. Also consider the fuel tank capacity. A generator that runs unattended overnight needs a tank large enough for the expected runtime, or an external fuel supply system.

Step 5: Plan the Power Distribution
Once you know the generator size, plan how the power reaches your equipment. A transfer switch is essential if the generator backs up a facility that also has utility power. The transfer switch isolates the generator from the grid and switches loads automatically or manually. Without it, backfeeding can kill a lineman working on the utility lines.
For portable generators, use heavy-duty extension cords rated for the current. For permanent installations, run conduit and install a subpanel that feeds only the essential equipment. This avoids the temptation to plug in non-essential loads that would overload the generator.
What to watch: Voltage drop in long cables. A 100-foot extension cord carrying a heavy load can drop voltage enough to damage motors. Use the next heavier gauge wire or place the generator closer to the loads.
Step 6: Verify with a Load Bank Test
Before relying on the generator for a critical operation, test it under load. A load bank is a device that simulates the electrical load. You can rent one or build a temporary resistive load with space heaters. The test should run the generator at its full intended load for at least an hour. Monitor voltage, frequency, and temperature.
This step catches problems that paper calculations miss: a voltage regulator that cannot hold steady under load, an engine that overheats, or a fuel system that starves at high output. If the generator passes the load bank test, you can trust it to deliver reliable power for demanding sites.
What to watch: Do the test in the same ambient conditions where the generator will operate. A generator that works fine in a 50-degree warehouse may struggle in a 100-degree outdoor site. Also check the exhaust routing. Diesel exhaust contains carbon monoxide, which is deadly. The generator must be placed outdoors or in a well-ventilated area with the exhaust directed away from doors and windows.
Step 7: Plan for Maintenance and Spare Parts
A properly sized generator still needs regular maintenance. Change the oil, fuel filter, and air filter according to the manufacturer's schedule. Keep spare belts, filters, and a set of fuses on hand. Diesel fuel can degrade over time if stored for months. Use a fuel stabilizer and a water separator to keep the fuel clean.
What to watch: A generator that sits unused for long periods may fail to start when needed. Run it under load at least once a month for 30 minutes. This burns off moisture, re-lubricates the engine, and keeps the alternator in good shape.

Putting It All Together
Sizing a diesel generator comes down to three numbers: the total running load, the largest starting surge, and the operating load factor. Add them up, apply the surge, and pick a generator that can handle the worst case without running at its ragged edge. A generator that is too small will trip breakers or stall under surge. One that is too large will waste fuel and shorten its own life through light-load running.
For many industrial applications, a generator that supplies reliable power for demanding sites is one that is sized to run at 60 to 80 percent of its rating during the heaviest expected load. That leaves headroom for starting surge and for future equipment additions. The extra few dollars spent on a slightly larger generator are often less than the cost of a single equipment failure caused by an overload.
Once the numbers are right, the rest is about installation, testing, and maintenance. A well-sized diesel generator, properly installed and maintained, will provide years of reliable power for demanding sites with minimal trouble.
❧